NV200: Seat and Bed is here (Rusty lee rock n roll)!

Click for: NV200 Campervan build index, Also all Necessary tools used. Full conversion spec here. All photos taken during build

In a normal sized van, like a VW, there are a multitude of suppliers selling ready made beds of all sizes and budgets and quality.

But, go for a custom sized bed and the choice plummets dramatically!

And for us, getting a bed/seat that fits exactly where we want it will make or break the van and make it usable (for us) or not.  Its the most critical thing which the whole van is based around.

Looking around, some of the Rock n roll beds have normal hinges which mean the cushions never fit properly (!) – so in bed position you have a gap, or in seat position they are squished, or the bed boards are loose.  We don’t want any of these….  So this limits the choice further.

As the NV200 will also be a car, we want 4 belted seats, and this brings into question “crash tested” beds or not.  Once you hit custom sizes this is impossible anyway.  Also, in my view, campervans/motorhomes will never be as safe as a car in the back anyway – and this includes coach built.  In a big off, regardless of how well tied down, bonded or bolted, wood furniture will rip out and stuff will fly around anyway, probably including fridges, batteries, gas bottles, knives etc….  Also, the rear of vans aren’t safety zones or have crash protection like a car.  And you can never get type approval or any other approval – best we can do is MOT standard.

As the seats will be seldom used, that’s the balance for us.

What we can do however, is ensure the bed/seat is strong and well made.  Some cheap ones will pass MOT but you can see how they’d react in an accident, bend or fail etc.  So we avoided these.  We studied pictures of approved beds, welding quality, angular bracing, size of steelwork etc, and then tried to find a maker whose beds were of similar ilk.

And we found VW Rusty Lee  (http://vwrustylee.com/ ) – who assured us he could do anything we wanted (!).

On his comments assuring we could get what we wanted, we bought the van 🙂 …..

…. then we went to see him once we got the van.

Our spec:-

  • Same type of build as his T4 3/4 bed
  • Taller to allow loo underneath
  • Narrower
  • Shorter
  • Angle braces for head rests
  • Different rear corner angle
  • 2x seat Belts
  • Gas strut assist
  • Reclining 🙂
  • Grey paint

Due to holidays the lead time was longer than hoped, but in truth, the bed was ready the first week we were ready for it.  Rusty Lee gave expert advice, suggested changes, told us we were mad (! – he may be right), gave advice on van which made us change how we did the floor, and was clearly an expert on his beds.

Also, the workmanship is excellent, seeing other beds made and the quality of the builds was impressive – clearly a skilled man.

Anyway, day of collection….

….

Well – we always said the van build will succeed or not based on how the bed works and everything fits around it.  And, well, WOW!  Rusty Lee is bloody awesome – we were impressed when we collected, but got it home and put it in the “right” position and its virtually mm perfect!  Everything we hoped was possible – will be!

  • The loo fits PERFECTLY and with enough room to box.
  • MASSIVE area for pull out drawer next to loo (other bed designs do not permit this)
  • MASSIVE rear area – our awning and outdoor chairs will fit here.
  • And the rest of the design impresses – watching how the bed works, what touches what (or not) – and its an incredible piece of engineering.
  • Furniture line can be exactly where hoped – so battery location and gas locker will fit where we hoped.

(Pics are showing NOT FITTED yet – just resting)

No, we aren’t on commission, but I’m quite pedantic (not the word Rusty used 🙂 ) – and this far suprasses my expectations.  We’ve tested it as a seat, and a bed, and it is exactly as we want (yes, small but that is our choice and works)

Cheers Rusty Lee!

DSCN1584 DSCN1585 DSCN1586 DSCN1587 DSCN1588 MG_1246 MG_3724

18 thoughts on “NV200: Seat and Bed is here (Rusty lee rock n roll)!”

  1. Looks great.
    We have a mitsubishi delica L300 and have ordered one of rustys standard 3/4 beds.
    What foam are you going with? you going for a memory/reflex laminated foam?

  2. Really enjoying reading the blog. Bed looks very impressive. I might have missed it but any chance you could give the overall size of made up bed (length and width). Cheers!

    1. Think frame is 950w x 1550l but board (to doors) is 1000w and 1650 I think. The loo has about 5mm clearance sideways when bed is down.

  3. Hi
    We have enjoyed reading about your adventures in your NV200 so much so that we have paid a deposit for a year old NV200 Combi.
    However we have just hit a bit of a snag as I have discovered that taking out the rear seats will be classed as a modification and will invalidate any insurance. This is now putting us off completing the purchase.
    Could I ask you who you are insured with as they presumably are ok with the changes you have made. Any advice would be greatly appreciated.

    1. I’m surprised removing rear seats in the combi would invalidate insurance?
      For the first year, I was with Brentacre (Mark Study) who insured it as a van during the conversion, and were aware of all changes so I was fully legit.
      Second year, Adrian Flux.

      My challenge was that I wanted a self-build campervan AND class-2 business insurance, and sadly the two didn’t readily mix.

      So the above two, especially Brentacre, were very very flexible in modifications and not *that* expensive. (Though told, my paperwork n renewal wasn’t 100% perfect, hence I left).

      1. Thanks. We are now the proud owners of a one year old NV200 Combi. I have removed the row of three seats and have it in writing off my insurance that they are ok about it as you said. The plan is to use it as it is for a while and then look to make modifications. Have bought a quechua pop up awning which is great.
        Cheers.

  4. I have been looking at the Nissan NV200 for some time but your conversion has now made up my mind.

    I was initially looking at the Combi but your comments have now made me look at the van. I noticed in one of your comments re insurance that you said you wanted it for business as well as pleasure.

    Did you get the VAT back on the vehicle based on the dual use?

    1. No, our business is not vat registered so that wasn’t an option. Business use for us is just commuting. It was a 100% private purchase away from the business.
      If it was used as a van for a VAT registered business use,, then you may be able to get the vat back and/or tax relief – but you would need to use it as a van for the business. See your accountant as it probably is pushing the boundaries 🙂 Using it as a van for 3 years then selling to yourself to convert may be possible – and why we see so many VW T5 trade vans!
      But, for us, nope – tax and vat fully paid 🙁

    1. The bed, all in with me making the boards and screwing them on, VW Rusty Lee making the frame, and a local company doing the foam and upholstery – was <£1k - maybe £550-600 for frame, £350-400 for upholstery. TBH - the frame is FANTASTIC - far better made than most - worth a LOT more IMO.

  5. andy/ mel

    re the rock n roll bed from Rusty Lee

    I contacted Rusty and he gave the same price for the bed frame. I am still at the decision stage re buying an NV200

    Could you give me the dimensions of the frame? L x W x D, please. I would like to put that in place temporarily before then making cupboards etc

    If I opt for an NV200 I will be looking to build using your amazing conversion as a guide. The information you have freely shared is very helpful.
    Thanks
    Jim

    1. Hi Jim. I’m reluctant to give you frame measurements as every van build is unique and lots of decisions were made in order to get the bed frame we did – such as what loo, front loo access, loo accessible overnight, belted seat (bolts stick out), flat front, rear NS corner cut out, what the side shape is etc. Some of those decisions affected other elements, like seat height etc. In the NV its all a compromise. An exact copy may be perfect for you, or a tweak here and there may make it better for you. FYI – I built the wardrobe after the bed was test fitted. So not the answer you want I’m afraid! If you are local you can always have a look and see what is similar and what isn’t?

  6. Hello Ryan and Mel

    I am hoping then that Rusty Lee would have kept the frame measurement detail for your vehicle.

    I can understand your reluctance to give me the measurements because as you say, situations differ but I am going to ask for exactly what you had done; the gas strut release lever etc. So hopefully, he would still have these dimensions recorded. I assume that the NV200 load area width wouldn’t differ across model variants.

    From your pictures and the known dimensions of the van, I can probably work out the width more or less. I would be planning to do as you did; i.e. position the bed, bolt temporarily to the van floor, then work the cupboard space out from that. It looks like the Offside wheel arch width and the leisure battery length subtracted from the width of the van in both the Nearside wheel arch for base width limit dimension and above bed width limit dimension.

    Maybe I will wait until I get the van and start doing some careful measuring from that point.

    You detailed pictures will also be very helpful.

    Anyway, thanks for your response.

    Kind regards
    Jim

Leave a Reply to Eric Rok Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.